My first Breakout board for printers. (second part)
After over two hours making tests on the printer, I have figured out that the printer has a procedure to become ready to print. This procedure is composed by several test routines that check all the sensors in the printer.
The biggest problem is that these routines are implemented at the same time.
There are four optical sensors in the printer. Two of then are optical encoders. One in the axis motor, that send the paper ahead and control it position. One in the printhead axis, that control the position of printhead. There are two common optical sensors to check the paper feed. One is in the mechanism that catch the paper and another is over the axis and it checks if the paper is in the right position over the axis. Both work together. The printer also have a routine to check if the cleaner mechanism is working well and this check out is made by the encoder sensor under the printhead. To start up, printer works like this:
1) Check if the up encoder on the printhead is working fine. To do that it moves the printhead for few millimeters from right to left and then from left to right.
2) There is a kind of brace that hold the printhead on the right position, to avoid damages to it. This brace is handled for the cleaner mechanism. When the motor of cleaner goes unclockwise, release this brace and allows the printhed to go across all axis. If the cleaner mechanism is not working fine, the printer shows a general error. Else,
3)At the same time, the printer checks the Paper Feed sensor and the encoder of axis motor. On power on, the sensor of Peper Feed must be a high signal (3.3 V). So the printer moves the motor unclockwise until this signal is high and then clockwise until it is a low signal. At same time, it checks the motor axis encoder, moving few millimeters forward and backward.
4)Printer checks the Paper Sensor to see if there is a paper jam inside of it. If the signal is high, there is no paper jam. If the signal is low, there is a paper jam and to solve that, printer moves the axis motor quickly forward and at the same time, does an entire rotation in the mechanism of the Paper Feed. If paper sensor is still low after some distance, the printer shows a general error.
5)Some printers also check the cartridges to see if it is all ok, but this is not the case of the printer I have bought.
6)After that, printer checks in it memory if it is time to clean the printhead. This is not a complicated task, so doesn't matter.
....Again out of space to write.
Recherche parmi différents professeurs en Anglais…
Corrections · 11
0
My first Breakout board for printers. (second part)
After over two hours making tests on the printer, I have figured out that the printer has a procedure to become ready to print. This procedure is composed by several test routines that check all the sensors in the printer.The biggest problem is that these routines are implemented at the same time.
There are four optical sensors in the printer. Two of then are optical encoders. One in the axis motor, that send the paper ahead and control its position. One in the printhead axis, that control the position of the printhead. There are two common optical sensors to check the paper feed. One is the mechanism that catches the paper and another is over the axis and it checks if the paper is in the right position over the axis. Both work together. The printer also have a routine to check if the cleaner mechanism is working well and this check out is made by the encoder sensor under the printhead. To start up, printer works like this:
1) Check if the up encoder on the printhead is working fine. To do that it moves the printhead for few millimeters from right to left and then from left to right.
2) There is a kind of brace that holds the printhead in the right position, to avoid damages to it. This brace is handled for the cleaner mechanism. When the motor of cleaner goes clockwise , release this brace and allows the printhead to go across all axis. If the cleaner mechanism is not working fine, the printer shows a general error. Else,
3)At the same time, the printer checks the Paper Feed sensor and the encoder of axis motor. On power on, the sensor of Peper Feed must be a high signal (3.3 V). So the printer moves the motor clockwise until this signal is high and then clockwise until it is a low signal. At the same time, it checks the motor axis encoder, moving few millimeters forward and backward.
4)Printer checks the Paper Sensor to see if there is a paper jam inside of it. If the signal is high, there is no paper jam. If the signal is low, there is a paper jam and to solve that, printer moves the axis motor quickly forward and at the same time, does an entire rotation in the mechanism of the Paper Feed. If the paper sensor is still low after some distance, the printer shows a general error.
5)Some printers also check the cartridges to see if it is all ok, but this is not the case of the printer I have bought.
6)After that, printer checks in its memory if it is time to clean the printhead. This is not a complicated task, so doesn't matter.
....Again out of space to write.
0
My first Breakout board for printers. (second part)
After over two hours doing tests on the printer, I have figured out that the printer has a procedure to become ready to print. This procedure is composed of several test routines that check all the sensors in the printer.The biggest problem is that these routines are implemented at the same time.
There are four optical sensors in the printer. Two of them are optical encoders. One in the axis motor, that sends the paper ahead and controls its position. One in the printhead axis, that controls the position of printhead. There are two common optical sensors to check the paper feed. One is in the mechanism that catches the paper and another is over the axis and it checks if the paper is in the right position over the axis. Both work together. The printer also has a routine to check if the cleaner mechanism is working well and this check is made by the encoder sensor under the printhead. To start up, the printer works like this:
1) Check if the encoder on the printhead is working fine. To do that it moves the printhead for few millimeters from right to left and then from left to right.
2) There is a kind of brace that holds the printhead in the right position, to avoid damaging it. This brace is handled for the cleaning mechanism. When the motor of cleaner goes counter-clockwise, it releases the brace and allows the printhead to go across all of the axes. If the cleaning mechanism is not working (well), the printer shows a general error.
3)At the same time, the printer checks the Paper Feed sensor and the encoder of the axis motor. On power up, the sensor of Paper Feed must be a high signal (3.3 V). So the printer moves the motor counter-clockwise until this signal is high and then clockwise until it is a low signal. At same time, it checks the motor axis encoder, moving few a milimeters forward and backward.
4) The printer checks the Paper Sensor to see if there is a paper jam inside of it. If the signal is high, there is no paper jam. If the signal is low, there is a paper jam and to solve that, the printer moves the axis motor forward quickly and at the same time, does an entire rotation of/inside the mechanism of the Paper Feed. If the paper sensor is still low after some time, the printer shows a general error.
5)Some printers also check the cartridges to see if it's all ok, but this is not the case with the printer I have bought.
6)After that, printer checks if it is time to clean the printhead. This is not a complicated task, so it doesn't matter.
FYI (plural of axis = axes)
0
Got it. I will try it next time I have something to tell.
0
Yes I understand, but what I suggest is that you make it in more parts, but each is shorter:)
0
Gillian, this is a kind of good advice. I just could not write about this subject in a short text.
Vous souhaitez progresser plus vite ?
Rejoignez cette communauté d'apprentissage et essayez les exercices gratuits !
Ne manquez pas cette occasion d'apprendre une langue depuis chez vous. Découvrez notre sélection de professeurs de langues expérimentés et inscrivez-vous dès maintenant à votre premier cours !
Commencez à apprendre aujourd'hui
